Material Density Reference Table

Density values in kg/m³ and g/cm³ for 80+ metals, plastics, woods, ceramics, liquids and gases.

Material density is the mass per unit volume (SI unit: kg/m³). It is a fundamental property used to calculate component weight, select materials for weight-critical applications, determine buoyancy, and size lifting equipment. This reference table lists densities for common metals, alloys, polymers, woods, ceramics, composites, liquids and gases. Values are at standard conditions (20 °C, 1 atm) unless otherwise noted.

Metals and alloys

Density values are for the pure metal or standard alloy at 20 °C. Alloy composition and heat treatment cause small variations from tabulated values.

MaterialDensity (kg/m³)Density (g/cm³)Notes
Aluminium (pure)27002.70Al 1100, commercially pure
Aluminium alloy 202427802.78High strength, aerospace
Aluminium alloy 606127002.70General purpose alloy
Aluminium alloy 707528102.81Highest strength Al alloy
Brass (60/40)85008.50CuZn40, free-cutting brass
Bronze (tin, 10%)88008.80CuSn10, bearing bronze
Cast iron (grey)72007.20Varies 6800–7800 by grade
Cast iron (ductile)71007.10Spheroidal graphite iron
Chromium71907.19Pure Cr
Cobalt89008.90Pure Co
Copper (pure)89608.96Cu-ETP, electrical grade
Gold1930019.30Pure Au
Inconel 62584408.44Ni-Cr superalloy
Iron (pure)78747.87Electrolytic iron
Lead1134011.34Pure Pb
Magnesium (pure)17401.74Lightest structural metal
Magnesium alloy AZ3117701.77Sheet and extrusion alloy
Nickel (pure)89088.91Pure Ni
Silver1050010.50Pure Ag
Stainless steel 30479007.9018Cr-8Ni austenitic
Stainless steel 31679807.9818Cr-10Ni-2Mo austenitic
Stainless steel 41077507.7513Cr martensitic
Steel (carbon, low)78507.85S235, S275, A36, mild steel
Steel (carbon, high)78707.871080, spring and tool steel
Steel (tool, H13)78007.80Hot-work tool steel
Titanium (pure)45104.51Grade 1–4 CP titanium
Titanium alloy Ti-6Al-4V44304.43Most common Ti alloy
Tungsten1930019.30Heaviest common metal
Zinc (pure)71337.13Pure Zn
Zinc alloy (Zamak)66006.60Die-casting alloy

30 rows

Plastics and polymers

MaterialDensity (kg/m³)Density (g/cm³)Notes
ABS1020–10501.02–1.05Acrylonitrile butadiene styrene
Acetal (POM)14101.41Delrin — good bearing material
HDPE930–9700.93–0.97High-density polyethylene
LDPE910–9400.91–0.94Low-density polyethylene
Nylon 6 (PA6)11301.13General purpose polyamide
Nylon 66 (PA66)11401.14Higher heat resistance
PEEK13201.32High-performance engineering polymer
Polycarbonate (PC)12001.20Transparent, impact resistant
Polypropylene (PP)9050.91Lightest common structural polymer
Polystyrene (PS)10501.05General purpose and HIPS
PTFE (Teflon)22002.20Chemically inert, high temp
PVC (rigid)13801.38Pipes, fittings, window profiles
Silicone rubber1100–16001.1–1.6Varies by filler and grade
UHMWPE930–9400.93–0.94Ultra-high molecular weight PE

14 rows

Woods, ceramics and other materials

MaterialDensity (kg/m³)Density (g/cm³)Notes
Balsa wood120–1700.12–0.17Lightest structural wood
Pine (softwood)500–7000.50–0.70Structural timber
Oak (hardwood)700–9000.70–0.90Flooring, furniture
Teak630–9000.63–0.90Marine and outdoor use
Plywood500–7000.50–0.70Structural panels
Concrete, plain24002.40Normal-weight mix, EN 1991-1-1: 24 kN/m³
Concrete, reinforced25002.50With normal steel content, EN 1991-1-1: 25 kN/m³
Reinforced concrete24002.40With rebar
Alumina (Al2O3)39003.90Technical ceramic
Silicon carbide (SiC)32003.20Abrasive and structural ceramic
Glass (soda-lime)25002.50Window and container glass
Granite2600–27002.60–2.70Dimension stone
CFRP (carbon fibre)1500–16001.50–1.60Unidirectional 60% fibre
GFRP (glass fibre)1700–21001.70–2.10Varies by resin and fibre
Water (20 °C)9981.00Reference liquid
Sea water10251.03Typical ocean density
Hydraulic oil (ISO VG 46)8700.87Mineral hydraulic fluid
Air (20 °C, 1 atm)1.200.0012Dry air at standard conditions

18 rows

Watch: Steel to Aluminium: 66% Lighter? Not for Stiffness

Steel to Aluminium: 66% Lighter? Not for Stiffness

YouTube Short · 0:29

The same 1000 × 500 × 10 mm plate weighs 39.25 kg in low-carbon steel (7,850 kg/m³) and 13.50 kg in aluminium 6061 (2,700 kg/m³): 66% lighter. But aluminium's Young's modulus is 69 GPa against 200 GPa, so the plate bends 2.9× more. Bending stiffness scales with E × t³: matching the steel plate takes 14.3 mm of aluminium and 19.25 kg, still 51% lighter, not 66%.

Plays in YouTube’s privacy-enhanced player; nothing loads from YouTube until you press play. Watch on YouTube

About the Material Density Reference Table

Sources

Classification: Typical reference values

Sources

  • CRC Handbook of Chemistry and Physics

    CRC Press

  • ASM Handbook, Volume 1 — Properties and Selection: Irons, Steels, and High-Performance Alloys

    ASM International

  • MatWeb material property database

    MatWeb

Densities are typical values for standard grades at room temperature (≈ 20 °C, 1 atm). Pure-element values are precise; alloy, plastic, wood and composite values span a range because composition, filler content, moisture and fibre fraction vary. A range is shown wherever that variation is significant.

How it was compiled

Density is mass divided by volume (ρ = m/V). For pure metals and elements the values are well-established physical constants. For alloys and engineered materials the values are representative of commonly supplied grades; where a material varies widely (woods, composites, cast iron) a range is given instead of a single figure.

How current it is

Classification: Stable (physical property)

Density is an intrinsic material property that does not change over time. The values themselves are stable; what changes is which grades and composites are commercially common. Confirm the exact grade density from a current supplier datasheet for design-critical weight calculations.

Limitations

  • Alloy density shifts slightly with exact composition and heat treatment — typically under 1% for metals, more for porous or filled materials.
  • Wood density varies with moisture content and species; the tabulated ranges are indicative, not design values.
  • Composite (CFRP/GFRP) density depends on fibre volume fraction and layup; the listed values assume a typical 60% fibre content.
  • Temperature affects density through thermal expansion. The effect is small for solids near room temperature but significant for gases and hot liquids.

Using it

  • For weight estimation use volume × density, and confirm the exact grade density from the supplier datasheet when weight is safety- or cost-critical.
  • Use specific gravity (density ÷ 1000 kg/m³) for quick buoyancy and fluid-selection comparisons — it is dimensionless and numerically equals density in g/cm³.
  • When comparing materials for lightweight design, compare specific strength (UTS/density) and specific stiffness (modulus/density), not density alone.

Units and notation

The SI unit is kg/m³; g/cm³ is numerically identical to specific gravity and is shown for convenience. 1 g/cm³ = 1000 kg/m³.

Frequently Asked Questions

How do I calculate the weight of a steel plate?

Weight (kg) = volume (m³) × density (kg/m³). For a steel plate 1000 mm × 500 mm × 10 mm: volume = 1.0 × 0.5 × 0.01 = 0.005 m³; weight = 0.005 × 7850 = 39.25 kg.

Why does density matter in material selection?

Density directly determines component weight and affects specific properties like specific strength (UTS/density) and specific stiffness (E/density). Aluminium has lower specific strength than steel but about one third the density, making it attractive for weight-critical structures where buckling rather than yield governs.

Does heat treatment change the density of steel?

Heat treatment causes only very small density changes (< 0.5%) because it changes the crystalline phase and residual stress state but not the atomic mass. For engineering calculations use the standard density regardless of temper.

How does the density of CFRP compare to aluminium?

CFRP at 1550 kg/m³ is about 57% of aluminium (2700 kg/m³) and only 20% of steel. Combined with its high tensile modulus, CFRP delivers exceptional specific stiffness — typically 3–5 × higher than structural metals.

What is specific gravity and how is it related to density?

Specific gravity (SG) is the ratio of a material's density to the density of water at 4 °C (1000 kg/m³). It is dimensionless and numerically equal to density in g/cm³, so steel at 7.85 g/cm³ has SG = 7.85.

Explore Knowledge

Go deeper with FlowUtil guides that explain the concepts behind this reference table.

Browse Knowledge Library