Chain Weight Calculator

Weight of a roller chain from its size and length, with a table by chain number.

Calculator

links
kg/m

Replaces the table figure, for attachments or conveyor chain.

Use the weight from your chain maker's catalogue for any load calculation. Roller chain is for power transmission. Do not use it for lifting unless its maker rates it for that.

Example Result

Your result will appear here

The calculated result will appear here after you press Calculate.

About the Chain Weight Calculator

Choose your chain number and enter its length or number of links. The calculator looks up the weight per foot, or per metre, and gives the total. Chain size sets the weight, and this page uses published maker figures, not a formula. Enter your own figure if you have the catalogue value for your chain.

How to Use the Chain Weight Calculator

  1. 1

    Choose the chain size.

  2. 2

    Enter the number of links, or switch to length.

  3. 3

    Pick the number of strands.

  4. 4

    Enter a catalogue weight if you have one, then press Calculate.

Chain Weight Calculator Examples

Frequently Asked Questions

How much does #40 roller chain weigh?

About 0.42 lb/ft, or 0.62 kg/m.

How much does #80 chain weigh?

About 1.7 lb/ft, or 2.5 kg/m.

How do I work out chain length from links?

Multiply the pitch by the number of links.

Does double-strand chain weigh twice as much?

Close to it. Check the catalogue for the exact figure.

Are ISO and ANSI chains the same weight?

No. They differ even at the same pitch, so use the size for your series.

Is this accurate enough for design?

It is a good estimate. Use your chain maker's value for a final design.

By O.E. — Partner, chairman of the board and CEO of a metal products manufacturer for 21 years; the company exports to 45 countries.

Drafted with AI assistance; calculations checked against primary sources and tested with the site's own code. About FlowUtil

Last reviewed

Weight by chain size

Average weights for single-strand ANSI roller chain, from one maker's published charts. Other makers vary by a few percent.

ChainPitchWeight (lb/ft)Weight (kg/m)
#251/4 in0.090.13
#353/8 in0.220.32
#411/2 in0.280.41
#401/2 in0.420.62
#505/8 in0.681.01
#603/4 in0.971.45
#801 in1.712.55
#1001 1/4 in2.653.95
#1201 1/2 in3.795.64
#1401 3/4 in4.967.38
#1602 in6.329.40

ISO 606 B-series chains are close but not the same. Distributor listings give about 0.7 kg/m for 08B-1, 1.0 for 10B-1, 1.2 for 12B-1 and 2.8 for 16B-1. Doubling the pitch makes a chain about four times heavier per foot, so size matters more than length.

Two-strand chain weighs about twice as much as one strand. Peer lists #40-2 at 0.85 lb/ft and #60-2 at 2.04 lb/ft.

Length comes first

Chain length = pitch × links. A chain of 100 links with a 1/2 in pitch is 50 in, or 4.17 ft. Links come from the sprocket sizes and centre distance, which the chain drive speed calculator gives you.

#40 chain, 100 links

  • Length: 100 × 0.5 in = 50 in = 4.17 ft
  • Weight: 4.17 × 0.417 = 1.74 lb (0.79 kg)

16B chain on a 10 m vertical run

  • Weight: 10 m × 2.8 kg/m = 28 kg
  • Load at the top: 28 × 9.81 = 275 N, before the working load

On a horizontal run, chain weight shows up as sag and friction. On a vertical or inclined run, it adds directly to the tension at the top. The chain pull calculator takes that load further, and a long chain also has to be started, so its mass adds to motor torque.

Where weight stops being the whole story

Use the weight from your chain maker's catalogue for any load calculation. Attachments, extended pins and side plates all add weight that a size chart does not show. Conveyor chain with rollers or slats has no general figure, so use its catalogue value in the custom field.

Add a margin on the structure and check it with the safety factor calculator.

Roller chain is for power transmission. Do not use it for lifting unless its maker rates it for that. Lifting chain is a different product with its own grades and rated loads: for example, 1/2 in Grade 80 weighs about 2.5 lb/ft. If you are lifting with wire rope, see the wire rope weight calculator.

Sources

  1. Peer Chain, Single Strand Roller Chain Size Chart, 2024.
  2. Peer Chain, ANSI Standard Roller Chain catalogue flyer.
  3. Renold chain listings through RS Components (08B-1 to 16B-1 masses).

Explore Knowledge

Deepen your understanding with in-depth engineering guides, formulas, and worked examples.

Browse Engineering Guides