Yield Strength
Quick Definition
Yield strength is the stress at which a material stops springing back and starts to deform permanently. For metals without a sharp yield point it is defined as the stress that leaves 0.2% permanent strain — the 0.2% proof stress, R_p0.2.
By O.E. — Partner, chairman of the board and CEO of a metal products manufacturer for 21 years; the company exports to 45 countries.
Drafted with AI assistance; calculations checked against primary sources and tested with the site's own code. About FlowUtil
Last reviewed
Yield Strength explained
Pull a steel bar and it first stretches elastically: stress and strain rise in proportion, and the bar returns to its original length when the load is removed. Keep pulling and you reach a stress at which the bar begins to stretch permanently — that stress is the yield strength. Below it a part can be loaded and unloaded indefinitely without changing shape; above it, it is permanently bent, stretched or dented, even if it has not broken.
Mild steel shows the moment clearly: the load drops slightly and the bar stretches at almost constant force — the yield point, reported as an upper value R_eH and a lower value R_eL. Most other metals — aluminium alloys, stainless steels, quenched-and-tempered steels — change from elastic to plastic gradually. For them, yield strength is defined by the 0.2% offset method: draw a line parallel to the elastic part of the stress–strain curve, starting at 0.2% strain, and read the stress where it crosses the curve. That stress, R_p0.2, is the value quoted on material certificates and in test standards such as ISO 6892-1.
Yield strength is lower than tensile strength, the highest stress the material reaches before it necks and breaks. Most structural and machine design keeps service stresses below yield by a safety factor so parts do not take a permanent set; design codes also limit stress relative to tensile strength, so both values matter.
Synonyms & Related Terms
Formula
R_e = F_e ÷ S₀ (force at yield ÷ original area)
R_p0.2 = stress at 0.2% permanent strain
ε_y = σ_y ÷ E (yield strain)
Real-World Example
A test bar of 10 mm diameter (S₀ = 78.54 mm²) starts to yield at a force of 27.9 kN. Its yield strength is 27,882 N ÷ 78.54 mm² = 355 MPa — the minimum for S355 structural steel. With Young's modulus at 210 GPa, the strain at that moment is 355 ÷ 210,000 = 0.0017, or 1,690 microstrain: the bar has stretched only 0.17% when it begins to yield, which is why strain gauges on steel structures read only a few hundred microstrain in service.
Worked Examples
Yield strain of A36 steel
σ_y = 250 MPa (36 ksi), E = 200 GPa: ε_y = 250 ÷ 200,000 = 0.00125 = 1,250 µε. A strain-gauge reading of 400 µε on an A36 member means it is at about a third of yield.
Reading a bolt's yield from its head marking
On an 8.8 bolt the first number × 100 is the nominal tensile strength (800 MPa) and the decimal × that value is the nominal yield: 0.8 × 800 = 640 MPa. A 10.9 bolt: 1,000 MPa nominal tensile, 0.9 × 1,000 = 900 MPa nominal yield; the standard's minimum is 940 MPa.
An allowable stress
An S275 plate up to 16 mm thick has a minimum yield of 275 MPa. With a safety factor of 1.5 the working stress limit is 275 ÷ 1.5 = 183 MPa.
Typical minimum yield strengths
| Material | Minimum yield |
|---|---|
| S235 structural steel (≤ 16 mm) | 235 MPa |
| ASTM A36 | 250 MPa (36 ksi) |
| S275 (≤ 16 mm) | 275 MPa |
| ASTM A572 Grade 50 | 345 MPa (50 ksi) |
| S355 (≤ 16 mm) | 355 MPa |
| Bolt class 8.8 (≤ M16) | 640 MPa |
| Bolt class 10.9 | 940 MPa |
| Bolt class 12.9 | 1,100 MPa |
Minimum values for structural steels fall slightly as plate thickness increases; use the figure for your thickness from the product standard or the mill certificate.
Yield point, yield strength and elastic limit
- Elastic limit — the highest stress with no permanent deformation at all; hard to measure, so rarely quoted.
- Yield point — the visible drop and plateau on a mild-steel curve (R_eH, R_eL).
- Yield strength — the engineering value: R_e where there is a yield point, R_p0.2 where there is not.
- Proof stress of a bolt — a separate, lower test value: the load a bolt must carry without measurable permanent stretch (580 MPa for an 8.8 bolt up to M16, against 640 MPa yield).
Why It Matters
Almost every strength check in structural and machine design compares a calculated stress with the yield strength divided by a safety factor: beams, shafts, pressure vessels, bolts. Yield strength also falls as temperature rises, so components in hot service are checked against yield at the operating temperature, not at room temperature.
Industry Applications
Sources
- ISO 6892-1, Metallic materials — Tensile testing — Part 1: Method of test at room temperature (definitions of R_eH, R_eL, R_p0.2; standard not opened)
- ISO 898-1, Mechanical properties of fasteners — minimum yield strengths of classes 8.8, 10.9 and 12.9 (read from fastener makers' technical pages)
- EN 10025-2 and ASTM A36 / A572 — minimum yield strengths of structural steels (standards not opened)
Related Standards
Frequently Asked Questions
What is the formula for yield strength?
R_e = F_e ÷ S₀: the force at which yielding starts divided by the original cross-sectional area. Where there is no clear yield point, the 0.2% offset stress R_p0.2 is used.
How do I find yield strength from a stress–strain curve?
Draw a line parallel to the straight elastic part, offset by 0.2% strain; the stress where it meets the curve is R_p0.2.
What is the yield strength of steel?
Common structural steels are 235–355 MPa (A36: 250 MPa, 36 ksi); quenched-and-tempered alloy steels exceed 900 MPa.
What is the yield strength of a bolt?
It is coded in the property class: 8.8 → 640 MPa (660 MPa above M16), 10.9 → 940 MPa, 12.9 → 1,100 MPa minimum.
What is yield strain?
The strain at the start of yielding, σ_y ÷ E — about 0.12–0.17% (1,250–1,700 µε) for structural steel.
Is yield strength the same as tensile strength?
No. Tensile strength is the maximum stress before fracture; yield strength is where permanent deformation begins and is always lower.
What is the yield ratio?
Yield strength ÷ tensile strength: around 0.6–0.7 for mild steel, 0.9 or more for high-strength steels and bolts — less warning before fracture.
See Also
Related Glossary Terms
Tensile Strength
Tensile strength, or ultimate tensile strength (UTS), is the highest stress a material can carry in tension: the maximum force in a tensile test divided by the original cross-section. Ductile metals reach it before they neck and break.
Stress
Stress is the internal force per unit area in a loaded material: σ = F ÷ A. Normal stress pulls or pushes across a section, and shear stress slides along it. It is measured in pascals (N/m²), MPa or psi.
Elasticity
Elasticity is a material's ability to return to its original shape after a load is removed. In engineering, it is measured by a modulus such as Young's modulus. In economics, the same word means how strongly demand responds to price.
Ductility
Ductility is how far a material can be stretched before it breaks. It is measured in a tensile test, as percent elongation or percent reduction of area. Steel, copper and aluminium are ductile; glass and cast iron are not.
Hardness
Hardness is a material's resistance to permanent indentation. It is measured by pressing a hard indenter into the surface under a set load, and reported on a scale such as Rockwell (HRC), Brinell (HB) or Vickers (HV). Each scale has its own number, so a hardness value must always name its scale.