Thread Stress Area Calculator

Find a bolt's tensile stress area and proof load, or convert pitch, TPI, lead and thread depth.

Calculator

mm
mm
MPa
MPa

This is a static area check. A critical joint needs a full bolted joint analysis.

Example Result

Your result will appear here

The calculated result will appear here after you press Calculate.

About the Thread Stress Area Calculator

A threaded bolt breaks at the thread, so its strength comes from less area than its nominal diameter suggests. That figure is the tensile stress area. Pick a thread and a bolt class to get the area, proof load and tensile load. The other two modes convert pitch to threads per inch, work out lead, and give the depth of a thread.

How to Use the Thread Stress Area Calculator

  1. 1

    Choose a mode: stress area, pitch and lead, or thread depth.

  2. 2

    For stress area, pick a thread and a property class or grade.

  3. 3

    For pitch or depth, enter a pitch in mm or threads per inch.

  4. 4

    Use the proof load as the limit for a tightened bolt, not the tensile load.

Thread Stress Area Calculator Examples

Frequently Asked Questions

What is the stress area of an M12 bolt?

84.3 mm² for the coarse M12 × 1.75 thread.

What is the proof strength of class 10.9?

830 MPa. Its minimum tensile strength is 1,040 MPa.

Why not use the nominal diameter?

The thread removes material, so the bolt fails through a smaller section.

Is stress area the same as root area?

No. It is a little larger, because it uses the average of the pitch and root diameters.

How do I convert TPI to pitch?

Divide 25.4 by TPI to get mm.

What is the difference between pitch and lead?

Pitch is the spacing of threads. Lead is the travel per turn, which is pitch × starts.

How deep is a metric thread?

About 0.61 × pitch on a bolt and 0.54 × pitch in a nut.

By O.E. — Partner, chairman of the board and CEO of a metal products manufacturer for 21 years; the company exports to 45 countries.

Drafted with AI assistance; calculations checked against primary sources and tested with the site's own code. About FlowUtil

Last reviewed

Where 0.9382 comes from

ISO 898-1 takes the area of a circle whose diameter is the average of the pitch diameter d₂ and the thread's root diameter d₃:

As = π/4 × ((d₂ + d₃) ÷ 2)²

With d₂ = d − 0.6495p and d₃ = d − 1.2269p, the average is d − 0.9382p. So As = π/4 × (d − 0.9382p)². For M16 × 2: d − 0.9382 × 2 = 14.124 mm, and As = 156.7 mm². Tables round this to 157 mm².

Inch threads use a different constant, because they are defined by threads per inch n: At = 0.7854 × (d − 0.9743 ÷ n)². For 1/2-13: 0.7854 × (0.5 − 0.0749)² = 0.1419 in². Machinery's Handbook gives another formula for steels above 100 ksi tensile strength, and the result is close for ordinary sizes.

From area to load

Multiply the area by the stress that matters. Proof stress gives the load the bolt must carry with no lasting stretch. Minimum tensile strength gives the load at which it may break. Take both from the bolt property class chart.

ThreadAs (mm²)8.8 proof (kN)8.8 tensile (kN)10.9 proof (kN)10.9 tensile (kN)
M8 × 1.2536.621.229.330.438.1
M10 × 1.558.033.646.448.160.3
M12 × 1.7584.348.967.470.087.7
M16 × 215791.1126130163
M20 × 2.5245147203203255
M24 × 3353212293293367

Class 8.8 steps up at M16: 580 and 800 MPa up to M16, then 600 and 830 MPa. Beware the figures 900 and 1,080 MPa, which you will see quoted for classes 10.9 and 12.9. They are nominal yield strengths. The proof stresses are 830 and 970 MPa.

A 1/2-13 Grade 5 bolt works the same way: 0.1419 in² × 85 ksi = 12,100 lbf proof load, and × 120 ksi = 17,000 lbf tensile load.

Fine threads add less than you might think

M16 × 1.5 has 167 mm², which is 6.8% more than M16 × 2. That gain comes from the shallower thread. A fine thread is also easier to strip in soft material, so check the thread engagement calculator before you switch.

Pitch, TPI and lead

Pitch is the distance from one thread to the next. Threads per inch is the same idea, turned over:

  • Pitch in mm = 25.4 ÷ TPI. So 13 TPI is 1.954 mm.
  • TPI = 25.4 ÷ pitch. So 1.75 mm is 14.51 TPI.

M12 × 1.75 and 1/2-13 look alike but will not mate. Their pitches differ, and so do their diameters.

Lead is how far a nut travels in one turn. Lead = pitch × starts. A normal bolt has one start, so lead equals pitch. A 2 mm lead screw with 4 starts moves 8 mm per turn.

To find pitch without a gauge, measure across 10 threads and divide by 10. For inch threads, count the threads in 1 in.

How deep a 60° thread is cut

Metric and Unified threads share one basic shape. H is the height of the sharp 60° triangle, and the real thread is cut shorter than that.

QuantityFormulaM12 × 1.75 (mm)1/2-13 (in)
Sharp triangle, H0.8660 p1.5160.0666
External thread depth, h₃0.6134 p1.0740.0472
Internal thread depth, H₁0.5413 p0.9470.0416

Use H₁ for a tapped hole, because the crest of an internal thread is cut back further. It explains why the tap drill size calculator gives 10.2 mm for M12 rather than 12 − 2 × 1.074. Production limits come from ISO 965 and ASME B1.1, not from these basic figures. Sizes for inch threads are in the UNC thread chart.

What the area leaves out

The proof load is a limit for one static bolt. It says nothing about preload, shear, bending or fatigue. A bolt tightened to 75% of proof load has a quarter of that load left, and the bolt stress calculator shows the stress once it is tightened.

Sources

  1. ISO, ISO 898-1, Mechanical properties of fasteners made of carbon steel and alloy steel, values as published by TR Fastenings.
  2. Fastenal, Torque-Tension Relationship, ISO 898-1 Property Classes, 2016.
  3. E. Oberg and others, Machinery's Handbook, Industrial Press.

Explore Knowledge

Deepen your understanding with in-depth engineering guides, formulas, and worked examples.

Browse Engineering Guides